您现在所在的位置:首页 >> 机械设计 >> 文章内容
Z30130X31型钻床控制系统的PLC改造 论文
双击自动滚屏 文章来源:   发布者:jsjlw99   发布时间:2009/7/6 15:00:38   阅读:2866
Z30130X31型钻床控制系统的PLC改造
 

摘 要:Z30130X31型摇臂钻床属于大型立式钻床,其传统的控制方式是利用继电器接触器原理控制。由于利用继电器接触器控制系统比较复杂,难于操作;因此本次设计是将其改造成为利用PLC控制,这样既可以提高生产效率,也可以增加其使用寿命。

首先通过对钻床工作原理的了解,然后对PLC的硬件和软件进行设计。根据钻床的工作要求选择合理的工作器件如:继电器,接触器等等,然后编写相应的程序语句表并绘制梯形图,再根据输入输出点数选择PLC型号,输入点数:22输出点数:17,所以本次设计选择FX2N-48MR型PLC并绘制硬件接线图;最后对程序进行模拟调试。

关键词:PLC;电动机;行程开关;断路器;控制按钮;控制开关;工作指示灯。

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Z30130X31 drilling machine control system's PLC transformation
 
Abstract: Z30130X31-arm drilling is a large vertical drilling, the traditional control method is the use of relay contacts Principle control. The use of the relay contactor control system more complicated and difficult operation, therefore this design is its use of a PLC control, this can enhance the efficiency of production and can also increase their service life.
  By drilling the first principle of understanding, and then the PLC hardware and software design. According to drilling requirements for the work of the work of a reasonable choice of devices such as: relays, contacts, etc., and then the preparation of the corresponding procedures and the mapping of ladder diagram sentences table, the light input and output points choose PLC models, the importation of points: 22 output points: 17, Therefore, this design options FX2N-48MR PLC and the mapping of hardware wiring diagram; Finally, the simulation debugging procedures.
Key words: PLC; motor; trip switch circuit breaker; control button control switch; work light.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
目    录
 
第一章 引言·······························································1
第二章 机床的主要参数及钻床的机械及运动形式···························2

[1] [2] [3]  下一页


【 字体: 打印本页 | 关闭窗口
此论文全套为收费论文。要想获得此全套论文和设计请联系本站客服QQ:31600328 欢迎你的访问!
 本文的地址是: http://www.jsjlw99.cn/Articlenews.asp?id=1870  转载请注明出处!
 您的姓名:
 评论正文:
 验证码:  
 
 [@2023/11/30 6:40:54]
   
 [@2022/12/17 19:13:43]
   
 [@2019/6/12 12:23:45]
   
 [@2019/6/2 21:24:28]
   
 [@2019/5/24 16:26:11]
   
 [@2019/5/14 16:02:29]
   
 [@2019/5/4 18:46:38]
   
 [@2019/4/22 19:27:07]
   
本类最新文章
机械设计目录 滚筒式抛丸清理机的设计  盐酸分解磷矿装置设计 
普通钻床改造为多轴钻床  减速器锥柱二级传动 论 带式输送机传动装置设计 
设为首页 | 收藏本站 | 过客留言 | 联系我们 | 友情链接 | 原创文章 | RSS订阅 | 管理入口

Copyright @ 2006-2008 Powered By 设计中心工作室  版权所有.
Email:31600328@qq.com QQ: 31600328
鄂ICP备05006890号 本站关键词:计算机毕业论文 计算机毕业设计